![]() This intake supports to over 600HP without any flow restrictions. Precise mounting support complementing a high quality install with an OEM plus touch. AIR RAM that connects to OEM cold air feed duct. While slight gains can be seen by pointing the velocity stack into oncoming air without the filter, this puts the engine at risk as unfiltered air can cause unwanted debris to enter your engine. After locating critical points for mounting and charge pipe routing, final design received a tailored Velocity Stack that blends in to the MAF. NOTICE: Hybrid Racing recommends always running the filter on the cold air intake. Fully assembled, the filter and velocity stack has a 6.25" overall height and 7.5" diameter. The velocity stack has a 2.25" overall height. All you need to connect it to your 3.5" cold air intake is a 3.5" silicone coupler and (2) hose clamps. The velocity stack has a 6" inlet and a 3" outlet. While a cold air intake and high-flow cone filter are. ![]() Included in each kit is a velocity stack, filter, and a hose clamp to connect the two together. In particular, modifying how air flows into and out of the engine can significantly impact performance. That said, the same sort of benefits can be seen by adding a similar bellmouth (in this case a velocity stack) to the end of your cold air intake. This bellmouth is added because it increases the efficiency of air moving through the pipe by as much as 70% in the right situations. If you've ever looked inside an intake manifold, you've noticed a curved "bellmouth" profile at the inlet of each intake runner. A well-designed cold air intake and high-flow cone filter are great ways to let your engine breath better, but a filter on the end of a pipe has its limitations. Paying close attention to how air flows into and out of your engine is an obvious place to start making modifications for optimal performance. I had to fold and bend the filter some to get it inside the furnace.When it comes to getting the most power out of your engine, the devil is in the details. I put the filter along the bottom - a 14x25x1 fit snug across the whole side (bottom if it was standing up). This is the air intake area - you can see the circulating fan on the right, behind the control board: There isn't any indication of where a filter should go, and no slot to slide it in or bar to hold it in place. ![]() I finally climbed up to the attic and took a good look at the furnace. The internal workings are the same for both styles. The other air intake systems are more elemental steel frames that hold on the air filter. The Powrflo uses a stylish aluminum cover with a v-shaped opening with a formed stainless steel mesh. Update: As is usually the case with me, I put off worrying about the furnace until it started getting too cold here at night. What is a PowrFlo Air Intake System We have two systems. Is there something I can do to put a filter in? Is it really harmful to run the furnace without one? Should I look into putting filters in all of my little air intakes around the house? So, for now, we've just been running the furnace without any filter. It looks like the previous owners had no idea either. When we bought the house, there were a few destroyed filters in the attic next to the furnace (all of different sizes, a few cut to different sizes, but no filter in the furnace. I don't have any idea what a "field-provided filter" is. A filter must be in place whenever the unit is operating A field-provided high-velocity filter is required for the unit to operate properly. This unit is not equipped with a filter or rack. The problem I am having is that I can't see where to install a filter! I can remove the front panel and see the bottom motor, but there's no where to actually put a filter.Īccording to the User's Information Manual: AdlerSpeed 5' Inlet OD Velocity Stack Bellmouth for Cold/Ram Air Intake/Turbo Engine Black. I have flexible ducts leading to the cold air intake "box" that is welded to the bottom of the furnace, and round flexible ducts leading from the hot air "box" to all of our vents (which are in the ceiling). These vents go up to the attic, and they're all routed into a big metal box which is appears to be welded to the bottom of the furnace.īecause this is kind of hard to imagine, I mocked up a little image of my setup (this isn't my actual furnace, just a similar picture I found on Google): We have intake vents in almost every room of the house (small vents, about 12" long by 8" tall). Because the furnace is installed in the attic, it is "laying down" on its side, and the incoming air is piped into what would be the bottom of the unit if it was standing up. I have a Lennox G40UH(X) series furnace, which is installed in our attic (We have a single-story house on a slab).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |